Today I share with you a set of important tips that every driver must work in his car to maintain them as follows:                                                                                                                                               

1 - Measuring the level of engine oil When measuring the level of oil level of the engine of the car, must first be the car in the horizontal level, and the engine to run to normal operating temperature, and then stop the engine by closing the contact key and wait about five minutes, From the place of the engine and clean thoroughly with a cloth that does not contain a barber, then place it again in the engine and raise and notice the level of oil, and must be between the signs of size and not be higher than the top mark or less than the bottom mark, and should not measure the level of oil and the engine in the case Rotation because this will give an inaccurate statement of oil output Engine.                        2. Tire pressure When tire pressure is measured, the calf must be cool, because the pressure gauge after a long car journey. The friction between the tire frame and the road increases the heat of the tires and thus increases the heat of the air inside it. The pressure increases and gives an incorrect reading of the value. Pressure inside the tires.

3. Brake oil The brake fluid is not supplied when the brake fluid is low, because the low brake fluid level indicates the erosion of the brake pedal and gives the brakes brake light to light up in the dashboard. The coil is eroded without giving any indication to the driver as the brake light does not light up. The brake fluid is provided only when it leaks or when any of the parts inside the cycle are changed. The use of brake oil should be strictly prohibited because it has a severe impact on the body paint. If it occurs and spills on the body of the vehicle, it should immediately pour a quantity of water onto the brake oil position on the body of the vehicle.


4. Battery cable When changing or repairing any electrical parts of the vehicle, start by removing the negative battery cable from its place so as not to shorten the electrical circuit of the vehicle. Also when the battery is changed, you must first remove the negative cable and remove the cable Before you remove any battery cable, you must first make sure that the ignition switch is in close position, and that all the keys of the lights are closed, so that the half parts of the vehicle are not damaged by the electronic circuit.
5. High temperature of the engine When the engine temperature suddenly rises, you must immediately take the right lane of the road and stop the car in a safe place by the road, and immediately close the ignition switch (contact) to turn the engine off the rotation, then open the hood - The existence of any leakage of water in the cooling cycle and work to prevent or repair and change what is necessary, ensure the safety of operation of the cooling fan, and after cooling the engine can open the radiator cover and ensure the presence of water inside, and also ensure the safety of water Radiator and have water in it up to the required level , To ensure the safety of the radiator cover, to ensure the safety of the radiator itself and the absence of anything that obscures the air.

6 - walk on the road avoid walking on the road behind trucks loaded with (sands or bricks or gravel or drums or any lengths such as iron or wood skewers etc.) as all of this fall at any moment suddenly in front of you on the road leads to accidents that do not thank her heels . Or at least sand may be blown on the windshield of the car, causing scratches or flickering, or glass falling, or the bricks falling to the ground, damaging the engine oil.

7 - Change the plugs Ignition (Bujiat) Take into account before changing the spark plugs (Bujiat) of the car to circulate well with compressed air to clean the dust that may be accumulated around, and after being removed from the place must rotate the engine several rolls with marches so that the engine can clean the dust around the springs The candle that is located in the cylinder is sent out, thus preventing the dust from entering the engine's cylinders and prolonging the life of the engine. You can then install the new joysticks after making sure that the gap is cleared at the recommended size.                                                                                                                                                                        8. Radiator water supply When the radiator water is detected, do not open the radiator cover and the engine is hot so that the pressure of the hot water does not rush to you and it will burn you. Radiator water should be supplied through the radiator cooler up to the upper mark level. Note that the water level in the radiator cooler increases and decreases automatically depending on the condition of the engine. It increases and the engine is hot and decreases when the engine is cold. Coldness. When the radiator is filled through the opening of its neck, it is hot and is waiting for it to cool slightly and slowly open the lid. Then the engine is turned on while the water is being supplied. The new cold water mixes with the hot water around the cylinders. اعلانك هنا